parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
I obtained this tree for about $10 as a rooted cutting in a 4" nursery pot. The sapling was planted in pumice and scoria. June 2014:
IMG_0321.JPG
After purchase, I slip potted it into an 8" round nursery pot.


March 2015:
IMG_0322.JPG


May 2015, showing a lack-of-water mishap: (and/or bad repotting aftercare)
IMG_7459.JPG

2015 was an impressive growing season. January 2016:
IMG_8594.JPG

Today, February 2017, in poor lighting after I repotted it into a 16" square grow box:
IMG_0301.JPG

I've done wiring on primary branches only. The sacrificial growths are intentionally long and pointing up. The newest lower branches may be replacements for some of the more coarse lower branches. For now, lots of waiting and growing is in order. I'll feed heavy after the first flush hardens off. The buds are swelling.

The root mass is well formed! I like the impact collanders have on roots. I've been using pumice, lava, and diatomite gravel for soil.
IMG_0299.JPG
 
Last edited:

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
More pics from last night…

Before:
IMG_0298.JPG

I put a lot of careful time and attention into raking the roots and then working fine lava in with a chopstick.
IMG_0300.JPG

When rotated 90° counter clockwise:
IMG_0302.JPG

When rotated 90° clockwise:
IMG_0305.JPG

The backside:
IMG_0303.JPG
 

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
My goals:
  • Thicken the trunk to at least 2" diameter
  • Ensure branches decrease in thickness as they go up the tree
  • Produce cuttings
  • Find the right height
  • Ramify!
I'm guessing it'll be ready for a nice pot after 4 more growing seasons.
 
Messages
1,309
Reaction score
2,482
Location
Finger Lakes Region, New York
USDA Zone
5
Do you see those long branches with no side shoots? the ones you cut back? Larch tend to only grow at the ends of the branches. Trim them consistently during the growing season and side branches will develop faster. Also larch branching seems to thicken faster the more foliage there is instead of allowing long sacrificial branches.
 

AlainK

Imperial Masterpiece
Messages
5,394
Reaction score
9,486
Location
Orléans, France, Europe
USDA Zone
9A
My goals:
  • Thicken the trunk to at least 2" diameter
  • Ensure branches decrease in thickness as they go up the tree
  • Produce cuttings
  • Find the right height
  • Ramify!
I'm guessing it'll be ready for a nice pot after 4 more growing seasons.

Hi parhamr,

Out of your 5 goals, I'm afraid that there's one you won't reach: "Produce cuttings". I think the chances are very low but what is there to risk when pruning?...

The rest of the programme seems OK ;)
 

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
It's way too early to be certain about this, but I have 1 of 12 dormant hardwood cuttings showing greenery after a week:
IMG_0334.JPG

About half of the 12 cuttings have shown bud swelling. I just need to keep up a good hand-misting routine :)

I'm expecting young cuttings, while in leaf, will have a much higher rate of success.
 

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
This seems promising. It's not yet desiccated and the 32W CFL seems to be what it likes/wants.

IMG_0539.JPG

One chaenomeles cutting from the same batch is also still going.
 

Paulpash

Masterpiece
Messages
2,008
Reaction score
6,019
Location
UK. Yorkshire
If those Larch cuttings take I will be more than impressed .....
 

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
This seems promising. I'm on 14-hour lighting cycles right now with a 32W CFL.
 

Attachments

  • IMG_0683.JPG
    IMG_0683.JPG
    242.4 KB · Views: 213

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
One cutting still appears very promising. The first to burst had dessicated and died. (But it did have about a pinky-nail's worth of roots!)

Many more are budding out, now. I've moved them from about 2000 to 8000 lumens of light.

IMG_0785.JPG
 

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
All of my cuttings have failed. I've not been able to mist them frequently enough. Now I see the value of a misting chamber :)
 

parhamr

Omono
Messages
1,767
Reaction score
6,213
Location
Portland, OR
USDA Zone
8
Tonight I wired most of the tree and removed unnecessary buds (crotches, downward, etc). The wiring was to bring branches downward and to fan them out so the foliage was overlapping less.

I think the bottom 2–5 branches might be removed in the future. For now, they’re useful to continue putting girth and taper into the trunk and for continuing to improve my wiring skills.
 

Attachments

  • 313442FD-5FED-4FB5-AEF1-6E3E62AFFA23.jpeg
    313442FD-5FED-4FB5-AEF1-6E3E62AFFA23.jpeg
    447.4 KB · Views: 368
  • 47CDF486-239A-4B46-8900-9C723D3DCF8E.jpeg
    47CDF486-239A-4B46-8900-9C723D3DCF8E.jpeg
    348.4 KB · Views: 379
Top Bottom